Blogwhere700

We replaced the RAID controller with an Adaptec 6805 because the old controller had some problems. The server run with ESXi 5.1. The problem with our Adaptec controller was that ESXi didn't support it out-of-the-box. It was supported in general but the driver was not included. We thought that the new ESXi 6 could contain the driver, but it didn't. The package provides the Adaptec SAS Enclosure installation files for Adaptec RAID controllers. These drivers are Microsoft Certified for: - Adaptec RAID 6405 using Firmware/BIOS b19176. Important Notes - During the installation of this file, be sure that you are logged in as the Administrator or as a user with Administrative rights. We have 2 Adaptec ASR-6405T manuals available for free PDF download: User Manual, Information Sheet Adaptec ASR-6405T User Manual (110 pages) Serial Attached SCSI RAID Controllers.

152 drivers total Last updated: May 25th 2016, 03:46 GMT RSS Feed

sort by:

3. Optional : Install Windows on the RAID volume

Si vous souhaitez installer Windows sur votre volume RAID, vous devrez d'abord configurer l'ordre de démarrage du BIOS de votre carte mère.
Pour cela, repérez l'option 'Boot' ou 'Boot priorities' et sélectionnez 'ASR-6405 RAID Ctlr #0 (...MB)' comme 1er périphérique de démarrage.

If you want to install Windows on your RAID volume, you must first configure the BIOS boot order of your motherboard.
To do this, locate the 'Boot' or 'Boot Priorities' menu and select 'ASR-6405 RAID Ctlr #0 (...MB)' as the first boot device.

Notes :
- If you want to install Windows on a RAID volume larger than 2 TB (2048 GB), you should use the GPT partition system. Which will require you to start your computer with the EFI system.
Néanmoins, tous les contrôleurs d'Adaptec ne sont pas compatibles avec le système EFI.
- If you want to install Windows on a RAID volume smaller than 2 TB (2048 GB), you can enable or disable the EFI system of your motherboard. If your Adaptec controller is not compatible with the EFI system, simply disable the EFI system to start your computer in LEGACY mode.
- The list of Adaptec controllers compatible with UEFI is available on the 'Adaptec controllers and UEFI motherboards' page of Adaptec.

Adaptec Raid 6405

Then, you need to load the RAID controller driver when installing Windows.
To do this, boot on the installation DVD of Windows Vista, 7, 8 or later and continue until the list of partitions.

In this list, you will not find your RAID volume. To see it, click on the 'Load Driver' link.

Insert the RAID Controller installation DVD or an USB key where you copied the RAID controller driver.
Then, click 'Browse'.

Select the folder corresponding to your operating system :
'windows-vista-ws-03-ws08driver' for Windows Vista / 7 / Server 2003 / Server 2008 in 32 Bits. Or the subfolder 'amd64' for 64 bits versions.
'windows8' for Windows 8 32 Bits or the subfolder 'amd64'for the 64 bits version.

If the wizard finds a driver compatible with your hardware, required drivers will be displayed.
Select all drivers displayed and click 'Next'.

Then, your RAID volume appears.
It remains only to install Windows on it.

4. Install the RAID controller driver

If Windows is already installed, you must install the RAID controller driver to allow Windows to use your RAID controller.
To do this, launch the Device Manager.

As you can see, Windows reports a problem with your RAID controller (in fact, missing the driver for this device).

To install the driver, simply right-click on 'RAID Controller' and click on 'Update Driver'.

Select 'Browse my computer for driver'.

Select the DVD drive or the folder that contains the RAID controller driver.

Check the 'Always trust software from « PMC - Sierra US, Inc »' box and click 'Install'.

Windows installs the driver.

The 'Adaptec RAID 6405' driver has been installed.

As you can see, the controller 'Adaptec RAID 6405' appears in storage controllers.

If you look in the hardware of your computer (right click on a partition -> Properties), you will find an Adaptec Array SCSI Disk Device 'hard drive'.

5. Initialization of the 'hard disk' and partitioning

As you may have noticed, the RAID volume doesn't appear yet in the workstation (or computer).
Makes sense because the 'hard drive' is not yet initialized nor partitioned.
To initialize and partition your 'hard drive', go to the start menu, right-click on Computer and click on 'Manage'.
Then, select 'Disk Management' and wait until this window appears.

Adaptec Raid 6405t Drivers

In this small window, you must choose the partition type :

• if your 'hard drive' (RAID volume) has a size smaller than 2 TB (2048 GB), you can choose 'master boot sector' to get a MBR or 'GPT Partition' for a GPT partition system.
• if your 'hard drive' (RAID volume) has a size larger than 2 TB (2048 GB), you should choose 'GPT partition'. Otherwise, you can only use a maximum of 2 TB.

For now, the 'hard drive' (RAID volume) is not partitioned. To create partitions, you only have to right click -> Create Volume.

In our case, we created two partitions on your 'hard drive'.

Now that it is partitioned, partitions are displayed in the workstation.

That is, your RAID volume is configured and ready for use.

Adaptec Raid 6405t Driver Installer

Note : Procedure based on the Adaptec QuickStart (english version at page 2).